收藏本站
HS SERIES DECODER DEVELOPMENT BOARD
USING THE DEVELOPMENT BOARDS
After unpacking the development system, attach an antenna to the decoder
board, install the supplied 9V battery, and turn on the power switch. The
5
8
encoder and decoder are set at the factory and will work straight out of the
box. To create a new operational setup, follow these steps:
1. On the decoder board, press and hold the LEARN button and then press the
1
9
CREATE_KEY button to enter Create Key Mode. Release the LEARN button
and press the CREATE_KEY button ten times to generate the KEY.
2. To use the infrared key transfer, press the GET_KEY button on the back of the
transmitter to activate the infrared receiver. Hold the back of the transmitter
2
6
7
13
11
10
12
14
close to the IR key exchange area on the decoder board until the MODE_IND
LED on the board lights up.
3. To set Control Permissions, press the LEARN button on the decoder board.
4. While the decoder’s MODE_IND line is flashing, press each button on the
transmitter that is to be granted recognition permission.
15
16
5. After all the desired data lines have been transmitted, press the LEARN button
again, or wait until the 15 second time-out occurs. The permissions will now be
3
4
17
18
19
20
saved in the decoder.
6. Transmit with one or all of the authorized data lines to confirm that the learn
process was successful.
Figure 1: HS Series Decoder Development Board
1. 9V Battery
2. Power Jack
TROUBLESHOOTING
If the boards fail to work out of the box, then try the following:
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
On-Off Switch
Voltage Regulator
QS Series USB Module
Prototype Area
Break-Out Header
RP-SMA Antenna Connector
LR Series Receiver
HS Series Decoder
Data Line LEDs
Indicator LEDs
Function Switch
? Check the batteries to make sure they are not dead.
? Make sure that the baud rate switch is set correctly on the decoder board.
? Make sure that the antenna is connected.
? Make sure that you set the Encryption Key correctly. This key is created by the
decoder and needs to be sent to the encoder before they will communicate.
? Make sure that you set your Control Permissions correctly. If you have not set
the handheld transmitter to use a particular line, then when you press a button
on the transmitter, the MODE_IND LED on the decoder board will light up, but
the data line LED will not light up.
If all of these appear to be in order, then you can call 800-736-6677 or e-mail
techsupport@linxtechnologies.com for technical support.
14.
15.
16.
17.
18.
19.
20.
Page 2
LEARN Button
SEND_KEY Button
CREATE_KEY Button
Key Input Jack (for hardwire key transfer)
IR Receiver Enable Button
IR Key Transfer Phototransistor and Diode (for IR key transfer)
Key Output Jack (for hardwire key transfer)
Page 3
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MDEV-418-HH-LR8-HS KIT DEV TX 418MHZ HS LONG-RANGE
MDEV-433-HH-CP8-MS KIT DEV TX 433MHZ MS SERIES
MDEV-433-HH-LR8-MS KIT DEV TX 433MHZ MS SER LONG-RG
MDEV-869-ES-USB KIT MASTER DEV 869MHZ ES USB
MDEV-900-HP3-PPS-RS232 KIT MASTER 900MHZ HP-3 SIP RS232
MDEV-900-HP3-SPS-USB KIT MASTER 900MHZ HP-3 USB SMD
MDEV-900-NT TRM 900 NT MASTER DEV SYSTEM
MDEV-GPS-SG KIT MASTER DEV GPS SG SERIES
相关代理商/技术参数
MDEV-418-HH-CP8-MS 功能描述:射频开发工具 MS Compact Handhld Trans Dev Sys 418MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MDEV-418-HH-KF1-MS 功能描述:射频开发工具 1 Button MS Keyfob Dev Sys 418MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MDEV-418-HH-KF2-MS 功能描述:射频开发工具 2 Button MS Keyfob Dev Sys 418MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MDEV-418-HH-KF3-MS 功能描述:射频开发工具 3 Button MS Keyfob Dev Sys 418MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MDEV-418-HH-KF4-MS 功能描述:射频开发工具 4 Button MS Keyfob Dev Sys 418MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MDEV-418-HH-KF5-MS 功能描述:射频开发工具 5 Button MS Keyfob Dev Sys 418MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MDEV-418-HH-KF-MS 功能描述:射频开发工具 1-5 Button Keyfob Dev Sys 418MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MDEV-418-HH-LR8-HS 功能描述:射频开发工具 HS LongRange Handhld Trans Dev Sys 418MHz RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V